CDOCS a SPEAR Company

Discussion Boards

General Discussion Post a New Topic

Here is the place to unwind and discuss anything.

  1. Discussion Boards
  2. General Discussion
Created Title
MTL lot numbers
By: Marc Thomas 3 Replies
Bilateral Buccal Bite trouble
By: Jeremy Lansford 4 Replies
Exporting .stl for orthodontist to review
By: Jeremy Lansford 2 Replies
Stains for C shades
By: Nathan Saydyk 6 Replies
GC Lisi vs Straumann Nice?
By: David Shapiro 2 Replies
Omnicam can not get past scan phase on almost edentulous patient.. help please.
By: David N.Moheban 7 Replies
Implant #10 with Volumax
By: Enrique Tuesta 7 Replies
CEREC IMPLANT CROWN #5
By: Sam Zamudio 2 Replies
5.2 update
By: James Stubblefield 1 Reply
SureSmile: How much IPR is too much?
By: Calvin Despain 6 Replies
How to remove a tooth in cerec
By: Robert Lang 3 Replies
Using an old scan to make a Biocopy on a new case
By: Steven Hernandez 2 Replies
Any way to use an Emax 40L block in an MCX?
By: James Stuart 2 Replies
Cleaning Black "Scuz"
By: Steve White 8 Replies
Implant scan question
By: Jim Hoye 3 Replies
Implant question using Dentsply Sirona Scan Post/Ti Base
By: Jim Hoye 2 Replies
First Transcrestal Sinus Lift
By: Luke Singh 5 Replies
patient in chair step bur broke and unable replace wrench not engaging
By: Karl McMillan 6 Replies
System hang
By: Armin Giessmann 14 Replies
Which Composite do you use for margin elevation technique?
By: Ray Kessler 15 Replies
Zirc + S1 oven cycle
By: Robert Feudo 1 Reply
CDoc course recommendations
By: Chad Ashley 2 Replies
Canine Guidance
By: Eric Kaleka
Vantage Point Presentation
By: Sameer Puri 8 Replies
Suresmile
By: Glenn Miller 5 Replies
Volumax failure
By: Jeremy Jones 12 Replies
why you might have an open margin
By: Dan Butterman 7 Replies
Immediate All on X workflow...depends on you! :)
By: Frankie Acosta 11 Replies
Milling Veneers
By: David Sorensen 1 Reply
Endo. #31
By: Damen Patel 3 Replies
PAtients moving to Durham NC
By: Joseph Chichetti 2 Replies
Need Help with Implant Bridge in Connect
By: Thomas Layton 3 Replies
Speedfire
By: Steven Justesen 1 Reply
Why you might have an open margin (with video)
By: Dan Butterman
Inlab waxup question
By: Edward Laco 4 Replies
Optisleep appliance life span?
By: Louis Passauer 2 Replies
Proper bite position height on Orthophos 11cm
By: Neil Johnson 1 Reply
Milling Zirconia Bridge with PrimeMill on EF mode
By: Douglas Hope 3 Replies
Guy says intraoral scanners are a terrible substitute for impression material
By: Robert Miller 14 Replies
How to take a Biocopy Scan on Biogeneric
By: Calvin Despain 1 Reply
Brand New primemill and CEREC MTL
By: Jeremy Lansford 5 Replies
Sicat function. Anybody used it? Tips?
By: Neil Johnson
Anklyos
By: Brad Barricklow 6 Replies
Blocking out undercuts
By: Edwin Mueller 3 Replies
InCoris Meso abutment block shades
By: Andy Stein 9 Replies
Favorite Block Materials?
By: Barrett Green 14 Replies
BLX 4.5 x 12 and 5.0 x12 chairside
By: Michael Saade 6 Replies
Tru Abutment
By: Naguib Youssef 7 Replies
Spray Glaze ZR
By: Thomas Layton
Need Endodontist in Phoenix area
By: Ray Ortiz 3 Replies
2023 Workshop Calendar

2023 Workshop Calendar
CDOCS GO Asst Training Launch

CDOCS GO Asst Training Launch
SPS Snider

SPS Snider

Contact Info

User Agreement | Privacy Statement

© Copyright 2024 CDOCS.com
CEREC is a registered trademark of DENTSPLY SIRONA Inc.

CDOCS LLC
Nationally Approved PACE Program Provider for FAGD/MAGD credit.
Approval does not imply acceptance by
any regulatory authority or AGD endorsement.
10/1/2022 to 9/30/2025.
Provider ID# 319544
refs/tags/releases/staging/2024-11-06.183800 - 62970db849d0bd3e60c73b5424b1c60c0da1a053 - 2024-11-06T18:38:48Z