CDOCS a SPEAR Company

Discussion Boards

General Discussion Post a New Topic

Here is the place to unwind and discuss anything.

Created Title
how do I burn out implant cement
By: Daniel Sorrick 4 Replies
Zirconia cracks in Speedfire
By: Stan Litras 15 Replies
Overdenture, then Hybrid, then lower implants, angioedema, oh my
By: David Sullivan 10 Replies
Residue on printed model
By: Darlenn Grace Ayan 5 Replies
Who makes the longest Zirc bridge block
By: Matt Schneider 8 Replies
splitter Valve for MCXL Vacuum
By: Christopher Kumfer 2 Replies
Dual Scan
By: William Strauss
help with two Maryland bridges
By: Yamen Ghamian 2 Replies
Help custom abutment for 3I Biomet Osseotite 3.75 external connection
By: JF Levesque 4 Replies
implant placement - patient has post-op pain
By: Ron Jarvis 14 Replies
Pt in Chair, help Delete button not working
By: Kolver Matos 5 Replies
Zirconia stains
By: Sergei Shirman 14 Replies
Dry Milling cyclone/accumulator
By: Scott Lundy 12 Replies
Define border tool inverting mandibular arch, but not maxillary arch in connect
By: McKinley Soult
Help with Truabutment
By: Richard Powell 4 Replies
PrimePrint Nitrogen Grade
By: Nathan Wong 2 Replies
CEREC is like charging your EV at home. It never gets old!
By: Enrique Tuesta 14 Replies
Does anyone have latest recommendations for antibiotic prophylaxis regimen?
By: Daniel Kim 15 Replies
Screw retained crown
By: Paul O'Kane 4 Replies
primemill water turned Kool-Aid red?
By: Noah Ariola-Tirella 12 Replies
Printing temps with PrimePrint problem
By: Russell Mann
Billing Sleep Apnea
By: Ike Heaphy 2 Replies
Hybrid Denture
By: Matthew Feeley 8 Replies
MALPRACTICE MOMENT - SPHENOID SINUS PATHOLOGY MISSED - WAS THE DDS AT FAULT OR NOT?
By: Thomas Kauffman 2 Replies
Zirconia Crown/Bridge Types Table
By: David Kerr 14 Replies
Patient in chair... Multiple Bridges, how to set up?
By: Casey Murdock 5 Replies
Sprue location on an Inlay/Onlay
By: Mojgan Mehranfard 6 Replies
what happens if you glaze before sintering?
By: Noah Ariola-Tirella 3 Replies
Ridge Lap Cantilever Implant Bridge
By: Natalie Stewart
cantilever "bridge" with zirconia blocks?
By: Noah Ariola-Tirella 2 Replies
HELP ORDERING CORRECT DIGITAL IMPRESSION BODY AND CEREC TIBASE IN OFFICE FOR STRAUMANN RC IMPLANT
By: Jonathan Gordon 2 Replies
Question: Do I need another milling unit to mill zirconia
By: Sandra Calleros DDS 18 Replies
Question about crown/bridge proposals and "blue" thin areas.
By: Noah Ariola-Tirella 30 Replies
Cerec software update
By: Kevin Ward 4 Replies
Should I cancel my cerec club?
By: Sergei Shirman 14 Replies
Thought of Dr. Chuck today
By: Kirsten Andrews 13 Replies
Katana one
By: Ryan Pitman 28 Replies
calibration and disposable sleeves
By: Glenn Miller 4 Replies
milling simultaneously on 2 mills
By: Daniel Sorrick 2 Replies
Prime print out of gas
By: James Stubblefield 3 Replies
Question about Cerec SW on design station
By: Enrique Tuesta 6 Replies
Please help with .DXD file - Bridge Design
By: David Sullivan 17 Replies
Tessera in my speed fire oven
By: Winnie Cheung 4 Replies
stl file to prime print
By: Kirsten Andrews 2 Replies
no guide sleeve
By: Tracy LaCanne 2 Replies
Technique for Restoring Tissue Level Implants with CEREC
By: David Sullivan 1 Reply
Material for Direct and Indirect Pulp Caps...
By: Nikki Holmes 4 Replies
Weird design blip
By: Marie Huguelet
Meena, Please help!
By: Darlenn Grace Ayan 2 Replies
"A milling unit error has been detected (force error). Please try again. If this problem persists,
By: David Kerr 7 Replies