Beautiful Katana STML on Atlantis Abutment
I am looking forward to delivering this case after using the Atlantis workflow. Once my Atlantis account was set up correctly, it's not only about the weborder.com setup, you need to let Dentsply Sirona know to set up your account for Omnicam scanning.
Once the approprate accounts are set up the workflow is a breeze and importing the Core File and using Biocopy is flawless.
The crown is Katana A1 STML, glazed only. The Atlantis Zirconia abutment is shade 20. The implant is Straumann 3.3 bone level.
I will post more photos once the crown and abutment is seated in the next week or so.
Great case Bill... have been wanting to see and do some on an anterior. I wonder when it will be an option for chairside multilayer anytime soon, and not just Premium...
Mark
Mark,
Good news, this case was done thru Chairside Connect and sent to Atlantis and then imported into Chairside 4.5.2 for me to finish the crown. I didn't use my Premium.
Thank you Dan. I look forward to using the Insertion Guide, no experience yet with it. Any advice?
On 4/19/2018 at 9:19 am, Bill Burkhart said...Mark,
Good news, this case was done thru Chairside Connect and sent to Atlantis and then imported into Chairside 4.5.2 for me to finish the crown. I didn't use my Premium.
Yep.... and it's a crown from there on... I've had a couple of cases scanned in chairside for implants where I would have like to have milled the Katana to compare side by side to e.Max, but it's not yet a veneering material available there. Still would like to see them side by side... but your case is completely fantastic...
Mark
On 4/19/2018 at 9:21 am, Bill Burkhart said...Thank you Dan. I look forward to using the Insertion Guide, no experience yet with it. Any advice?
It's really easy. The abutment fits in only one way, so load it before the patient gets there with the screw inside. The guide will fit around the adjacent teeth, once seated, just hand tighten the screw and remove the guide. Try in crown and torque as normal, but go slow torquing and be careful not to go higher than the recommended torque with zirc abutments.
Great looking case Bill. Would love to see intra-oral pics once you deliver.
My only hesitation (based on research and previous experiences) is that I am very uneasy with all-zirc abutments, especially on narrow diameter restorative platforms such as the NC. I personally have completely abandoned all-zirc abutments.
Farhad
On 4/19/2018 at 9:39 am, Farhad Boltchi said...Great looking case Bill. Would love to see intra-oral pics once you deliver.
My only hesitation (based on research and previous experiences) is that I am very uneasy with all-zirc abutments, especially on narrow diameter restorative platforms such as the NC. I personally have completely abandoned all-zirc abutments.
Farhad
Farhad,
What are your design parameters (gingival depths) for the Atlantis abutments when in anterior and using gold titanium custom abutments?
That A1 block you got on there sure does look pretty...where oh where did you find that!!!
Nice job man that looks sweet. Indenco spray glaze?
On 4/19/2018 at 2:37 pm, Kurt Kwiatkowski said...Farhad,
What are your design parameters (gingival depths) for the Atlantis abutments when in anterior and using gold titanium custom abutments?
Buccal: 1mm subgingival
Interproximal: 0.5-1 mm subgingival
Palatal/Lingual: 0.5 mm subgingival or equigingival
If the buccal tissue thickness is 2 mm or more the color of the abutment will not have an effect on the final esthetic outcome (Jung et al.).
Farhad
Jarrod,
Yes, Idenco spray glaze. And thanks for supplying the block after I had a milling issue with my block!
