Sponsored by Kuraray

Patient Presentation

An 80-year-old male presented with what he considered to be unattractive teeth due to failing composite bondings that chipped away over time, creating unsightly patches (Figure 1). Specifically, the patient stated he wanted younger-looking teeth and was tired of having the composites replaced every few years, and therefore desired an esthetic and lasting solution. Furthermore, upon clinical examination and evaluation of radiographs, a diagnosis of recurrent decay was established on teeth #s 6 through 11.

Figure 1: Pre-op photo of teeth #s 6-11.

Material

A multilayered translucent material, KATANA™ Zirconia STML (Kuraray Noritake), was chosen to restore the patient’s teeth as it provides optimal strength and esthetics without the need for external stains. The multilayered block consists of four layers of zirconia in graduated shades, including an enamel layer, two transition layers and a body (dentin) layer. This material requires approximately 8 to 10 minutes milling time (dry milling) per unit in the CEREC® MC XL milling chamber, and 30 minutes sintering in the CEREC SpeedFire.

Treatment Steps and Technique

Step 1: Preparation

Teeth #s 6 through 11 were prepared as minimally as possible to accept KATANA™ Zirconia STML crowns (Figure 2). The CEREC Biojaw function, along with CEREC Biocopy, morphology and positioning tools were used to design the restorations in an effort to keep the size of the teeth similar to the patient’s existing teeth, but with improved morphology. Additionally, it was decided to add more incisal embrasures, as the patient was unhappy with the flat, worn down look of his natural teeth.

 
Figure 2: Preparations ready for digital scans.

Step 2: Scanning

The following scans were captured: Upper Biocopy, lower jaw and buccal bite. A preparation scan was also taken in the upper jaw after preparing the teeth with crown preps (Figures 3 & 4).

 
Figure 3: Scan of crown preps with gingival margins delineated.

Figure 4: Buccal preps scan.

Step 3: Designing

After an initial proposal was received with the Biogeneric Individual method, the Biojaw method was utilized to generate a design that was identical to the Biocopy in terms of length and width, but also satisfying the patient’s want of better shaped and younger-looking teeth. A shape was chosen that provided more incisal embrasures to avoid getting the flat, worn-down look of the incisal edges (Figure 5).

 
Figure 5: Biogeneric crown proposals.

Step 4: Milling

Each unit was milled in the MC XL, which was used for its ability to dry mill Zirconia. The “Fine” milling parameter was chosen as this case was not “same-day seating” so time was not an issue. That said, each of the six restorations required about 8 to 10 minutes total milling time.

Step 5: Firing

The restorations were fired in the CEREC SpeedFire for approximately 30 minutes.

Step 6: Glazing 

The inherent multilayer shading of the KATANA™ material produces a natural shade gradient, resulting in no need for additional stains. A light coating of Indenco Spray Glaze was applied to each restoration to impart a natural luster.

Step 7: Cementation

The intaglio of each restoration was sandblasted with alumina powder as a mechanical etchant, and then rinsed and dried thoroughly in preparation for cementation. Next, following manufacturer’s instructions for use, CLEARFIL™ CERAMIC PRIMER PLUS (Kuraray Noritake) was applied to the intaglio of each restoration, followed by PANAVIA™ V5 Tooth Primer to each tooth prep, and lastly PANAVIA™ V5 Cement to the intaglio of each restoration prior to final seating.

Conclusion

The patient was extremely happy with the final results as it met all his desires of uniform, younger-looking teeth with no patchwork (Figure 6). From a clinician’s point of view, I enjoyed working with a material that was easy to mill, along with high strength and excellent esthetics right out of the milling chamber.

 
Figure 6: Post-op view of seated KATANA™ Zirconia STML crowns.

Great as always!

Really nice work Dhaval....keep it up fella!

Chris